09 April 2016

WW1 German ships, part 2

With a little bit of spare time, I was able to make a little more progress with my WTJ 1/1800 ships. 

Magdeburg and Strassburg, and their masts.  I am not certain of the diameter of the brass rod used for the masts, but the yards are made of 0.006" brass wire (the long piece in the pic above).  Again, the mounting holes for the masts are printed into the WTJ cruisers, so just a bit of glue and in they go.

It is a different story with the TB's.  Their masts are also made from the thin brass wire, but I had to use a drill bit to make a hole for them.  I did not put yards on the masts for the TB's.

All of my 1/1800 ships now have their masts, although it is a bit hard to see from that angle.  Primer will make it much easier to see - more pics after that!

02 April 2016

WW1 Russian ships, part 3

Inspiration can strike suddenly, and this time I took advantage of the situation and worked on my WTJ ships a bit.

Here is my small flotilla of 1/1800 ships - German cruisers on the left, Russians on the right.  One can see that I have already primed the first Russian cruiser - Bogatyr - but I forgot one small detail... masts!  So, back to work.

I have some thin brass wire that I use for masts, and this time I decided to use plastic rod as well.

Before putting in the masts, I looked around for some pictures to help guide the work.  The WTJ ships have holes for masts already present in the model, in cruisers and larger at least, so siting the masts was not a problem, and I found a pair of pictures in one of my books - The Imperial Russian Navy by A.J. Watts - showing differences between Bogatyr and Oleg.  The book shows that Oleg has a slightly different bridge structure, without searchlight wings, and the masts are slightly different also.

In the pics below, one can just barely see the trimmed bridgework on Oleg, the rightmost cruiser.

Bogatyr from the bow

Oleg from the bow

It will be difficult to see the change until I get some primer on him.

And, some simple masts:

Bogatyr (the grey one) has slightly shorter masts, and Oleg has a lookout position on the mainmast.  I think, after the fact, that using the plastic rod is a bit off for the yards.  I will not repeat it with the German ships but the rest of the Russians will, except using the same brass rod as the masts.

20 March 2016

Ships from Valiant

Yet another new arrival:

These miniatures are from the Ramming Speed line from Valiant Enterprises.  At 1/900 scale, they are right between the almost too small (for me!) 1/1200 ships and the oddly shaped 1/600 line from Xyston.  I just can not put my finger on why the Xyston ships look off to me, but I am finding that I really do not want to work on them.

The variety of ships above were selected in order to flesh out my idea of what types of miniatures from Valiant could fill out the roles for Tékumel naval gaming.  Since the Valiant selection is limited, I am being careful about filling those roles in a fashion that is easily identifiable on the table top.  The information on the Valiant website has the triremes at the same length as the quinqueremes, so I am hoping that the wider beam of the quinquereme will make up for that.

Here is a comparison pic:

Each square is ¼".

Lots of good news in this pic.  The triremes are slightly shorter than the quinquereme, which is good.  Also, the triremes have a noticeable difference in beam from the quinquereme, and this will alter even more once the oar banks are attached.

 In my mind, the ships types will correspond in the following fashion:

     The pentekonter from Valiant (not shown above) will represent the Tékumeli séscha;

     Triremes will be the srügánta;

     Quinqueremes will represent the qél;

     Heptares and dekares (not pictured above) will be the Tékumeli zírunel.

The Valiant ships are plain enough that modifications will be easier than on the Xyston models - I intend to try to make some ships that look something akin to the ships illustrated in this wonderful post about Tékumel naval actions.

Although it seems simple, that bit of organization posted above is a weight off my shoulders!

15 February 2016

New project, and old

Just a quick pic or two:

On the left, my new 1/1800 ships from WTJ, with a pair of extras that were sent just in case some of my order fell afoul of a production problem.  Awesome service from WTJ!  Now, for some primer...

And on the right, one of my 1/600 Xyston ancient vessels, and assorted bits.  I am going to take another look at this scale for my Tékumel naval project.  One item that I can see already is the size of the 'castle' from Xyston.  It seems to be slightly small.  A scratch-built replacement might be in order.

Lastly, the Tékumel naval project got another boost with this:

I finally purchased my copy, and I am looking forward to reading through it again.

30 January 2016

Ships from WTJ!

Finally had some time to post this... my small, test order with WTJ arrived some time ago.  I ordered just a few ships - SMS Magdeburg and V167 for the Germans, and cruisers Oleg and Bogatyr and TB Boiki for the Russians.  Here is a quick pic:

Bogatyr is the top, Magdeburg is the bottom.  These ships are in 1/1800 scale.  The translucent material makes it difficult to get a good photograph of them, so once they are primed I will take a better set of pics.  Right now, they are soaking in some soapy water...